Free eBook Download

Content Inside:

Mitsubishi motors introduced 4G9 engine in August 1996, its a series of straight 4 automobile engine with 16-valve, and use both single- and double- overhead camshaft heads. This workshop manual contains procedures for removal, disassembly, inspection, adjustment, reassembly and installation etc. This manual divided into several section as follows: Specifications, special tools, ignition system, drive belt and timing belt, fuel and emission control system, intake manifold and water pump, exhaust manifold, turbo charger, rocker arms and camshaft, cylinder head and valves, front case and oil pump, piston and connecting rod, crankshaft, cylinder block, flywheel and drive plate. Engine diagram, exploded views and part list. This workshop manual available to download in pdf format consist of 101 pages.
More →

Content Inside:

This manual follows contain information about Boeing design especially the material selection. Table of content: Introduction, Material designation, environmental considerations, references, material selection, flat products: foil sheet and strip, plate, bar-rolled and drawn, forged blocks, forged bar, hand forgings and die forgings, Castings, Tubing, Ducting, Extrusions, Spring Wire, Comparative Strengths, drawing requirements and notes. List of figures: General advantages and limitations of titanium, physical properties and other features. Comparative strength, wall thickness for titanium hydraulic tubing in accordance with BMS7-234.
More →

Content Inside:

This document published by Light Aircraft Manufacturers Association of Canada, by reading this document you’ll find information about design standards for advanced ultra-light aeroplanes. Its divided into 7 chapters as follow: Chapter A - General 1, 1. Applicability 1, 2. Advanced Ultra-Light Aeroplane Category 1, 3. Minimum Useful Load 1, 4. Maximum Empty Mass (Weight) 1. Chapter B - Flight 2, 5. Proof of Compliance 2 6. Load Distribution Limits 2,,7. Propeller Speed and Pitch Limits 2, 8. Performance, General 2, 9. Stalling Speeds 2, 10. Take-off 2, 11. Climb: All engines Operating 3, 12. Landing 3, 13. Balked Landing 3, 14. Controllability and Manoeuvrability 3, 15. Longitudinal Control 4 16. Directional and Lateral Control 4, 17. Static Longitudinal Stability 4, 18. Static Directional and Lateral Stability 4, 19. Dynamic Stability 4, 20. Wings Level Stall 4, 21. Turning Flight and Accelerated Stalls 4, 22. Directional Stability and Control 5. Chapter C - Structure 6 - Loads, Factor of Safety, Strength and Deformation, Proof of Structure, Control System and Supporting Structure, Ground Load Conditions, Braked Roll Conditions, Supplementary Conditions for Tail Wheel. Supplementary Conditions for Nose Wheel, Water Load Conditions, Emergency Landing Conditions. Chapter D - Design and Construction: Materials and Workmanship, Fabrication Methods, Self-Locking Nuts, Protection of Structure, Proof of Strength - Wings, Control System - Operation Test. Chapter E - Powerplant: Installation, Engines, Fuel Tank Tests, Fuel Tank Vents, Fuel Strainer or Filter, Induction System Icing Protection. Chapter F - Equipment: Flight and Navigation Instruments, Powerplant Instruments, Miscellaneous Equipment, Safety Belts and Harnesses. Chapter G - Operating Limitations and Information: Weight and Centre of Gravity, Powerplant Limitations, Instructions for Continued Airworthiness, Aeroplane Manual, Operating Limitations, Operating Procedures.
More →

Content Inside:

Dell Latitude E6400 laptop computer is a business mobile pc powered with 2.26GHz Intel Core 2 Duo P8400 processor, 2GB, 667MHz DDR2 memory, 160GB 7,200rpm Hard drive. Dell Latitude E6400 measures 13.1×9.4×1.2 inches and for the graphic displays it use Nvidia Quadro NVS 160M. This Dell Latitude E6400 service manual will guide you to repair this laptop, and its divided into following sections: Troubleshooting, Working on Your Computer, Base Assembly, Hinge Covers, Hard Drive, WLAN/WiMax Card, WWAN Card, WPAN (UWB/BT) Card, FCM, Fan, Processor Heatsink Assembly Processor Module, Memory, Coin-Cell Battery, Modular Drive. LED Cover, Keyboard, Modem, Right Speaker Grill/Fingerprint Reader Assembly, Palm Rest Assembly, Card Cage, 1394 Card, RJ-11 Modem Connector, System Board Assembly, I/O Card, DC Power Cable, Battery Latch Assembly, Display Assembly, Flashing the BIOS. this service manual available to download in html format on zipped file. You need to extract it and then open with your favorite web browser, enjoy!
More →

Content Inside:

HP Pavillion dv3-2100 is a notebook pc that especially designed for entertainment purpose, withe the new 16:9 aspect ratio widescreen panel offers you a new screen size that is ideal for both computing and entertainment modes. Use the ample horizontal space for widget and toolbars and enjoy a great movie experience in their original format. This document is a troubleshooting reference used for maintaining and servicing the computer. It provides comprehensive information on identifying computer features, components, and spare parts; troubleshooting computer problems; and performing computer disassembly procedures. Section index: Contents, product description, external component identifications, illustrated parts catalog, exploded views, removal and replacement procedures, tools required, service consideration, component replacement procedures, Computer feet, Battery, Hard drive, Memory module, WLAN module, RTC battery, Keyboard, Speaker assembly, Display assembly. Backup and recovery guide. This service manual document available to download in pdf format consist of 154 pages.
More →

Content Inside:

Its a service manual document for hp LCD TV models: Hp HD LCD TV Service Manual for LT3200-LT4700 Series. Here you’ll find complete guide to repair, assemble, disassemble, troubleshooting the hp LCD tv. This document contain information as follows: Important service safety precautions, warnings and cautions, safe handling and servicing, repair tips, product information and specifications, LCD panel module, I/O Connectors, Factory preset display modes, remote control, tv connectors, replaceable part list, removal and replacement guide, removal procedures for:pesdetal, back cover, function keyboard, infrared board, main board, power supply, speakers, control board, front bezel. Diagnostic procedures LED indicators, Chassis layour and overall wiring diagrams. This service manual document available to download in pdf format consist of 102 pages.
More →

Content Inside:

Step by step Intake system installation instruction for 07-09 Toyota Camry/09 Venza V6-3.5L, tools needed: Flat Blade Screwdriver,
Phillips Screwdriver, Ratchet, Extension, 10mm Socket, Pliers, 10mm Wrench, 8mm wrench, 3mm Allen Wrench. Step by step guide: Turn the ignition OFF and disconnect the vehicle’s negative battery cable. Disconnect the mass sensor electrical connection
by depressing the center tab and gently pulling the harness away from the mass air sensor. Release the two wiring harness clips from the air box lid. Gently pull the engine cover upward to release it from the mounting grommets. Once released, Remove
engine cover from the vehicle and set aside. Disconnect the vacuum line from the intake manifold plenum connection. Disconnect the vacuum line from the upper air box lid. Disconnect the intake tube plenum vacuum line. Disconnect the two vacuum lines from the “Vacuum switching valve.” Disconnect the two vacuum lines from the factory “T” fi tting. Remove the screw securing the “Vacuum switching valve” to the stock fresh air duct. Place the “Vacuum switching valve” in a position that will allow ample clearance to work around. Remove the air fi lter. Remove the three bolts that secure the lower air box to the mounting bracket. This installation guide consist of 34 steps with pictures. Available to download in pdf format.
More →

Content Inside:

This document describes an example of an Oracle 9i Standard Edition database installation under RedHat Linux 8.x and 9.x. This document intends to show a simplified installation sequence for Oracle 9i database on RedHat Linux 8.x and 9.x. It is meant only as an example and if one intends to follow it, he/she should have in mind their own version of Linux, Oracle distribution and specific parameters of their own PC system. Getting Started guide: 2.1 Downloading Oracle 9i database, 2.2 Creating the CDs, Creating the CD images, Burning the CDs, 3. Pre?installation, 3.1 System Requirements, 3.3 JRE, 3.4 Setup tasks to perform as root user, Kernel Tune?up, Read and set the semaphore parameters, Read and set the shared memory parameters, Groups and accounts, Mount points and permissions, 3.5 Setup tasks to perform as oracle user, 4. Installation, 4.1 Mounting the CDs (before or during the installation), 4.2 Running the installer, 4.3 Installation screens and steps, UNIX Group Name Screen, File Locations Screen, Available Products Screen, Installation Types Screen, Database Configuration Screen, Database Identification Screen, Database File Location Screen, Database Character Set Screen, Summary Screen, Install Screen, Configuration Tools Screen, troubleshooting guide, Database Configuration Assistant, Troubleshooting updates, 5.2 Script for automatic startup on boot.
More →

Content Inside:

Your server is a highly complicated system of interdependent processes configured to offer simple, reliable, secure and high performance data and network services to your organization. When kept wellmaintained, Linux systems are a true marvel of engineering. And always remember there is a very large community out there with a wealth of information freely available, at all levels of understanding. Logging Into the Server, The server can be accessed for interactive login via the physical system console or from any computer on the networks by using SSH (Secure Shell). Adding a User: should start with letters and not contain any special characters other than numbers. This will be their login ID and the first part of their email address at your domain. Deleting a User: Just specify the user ID to be deleted. If you would also like to remove all of their email and any files
stored in their home directories, add the ‘r’ switch: Enabling or Disabling Shell Access for a User, Changing a User Password, Adding a User for Windows File Sharing Access. Deleting a User from Windows File Sharing Access. Updating the Server’s OS and Applications. Shutting the Server Down.
More →

Content Inside:

The purpose of this tutorial is to give you a sense of “what it is like” to build an ASP.NET MVC application. In this tutorial, I blast through building an entire ASP.NET MVC application from start to finish. I show you how to build a simple Tasklist application. Because the goal is to keep things simple, we’ll be building a very simple Tasklist application. Our simple Tasklist application will allow us to do three things: List a set of task, Create new tasks, Mark a task as completed. Creating an ASP.NET MVC Web Application Project. An ASP.NET MVC application has a standard set of folders: a Models, Views, and Controllers folder. You can see this standard set of folders in the Solution Explorer window. We’ll need to add files to the Models, Views, and Controllers folders to build our TaskList application. Creating the Controller Typically, when building an ASP.NET MVC application, you’ll start by building a controller. Each browser request made against an ASP.NET MVC application is handled by a controller. A controller contains the application logic that is responsible for responding to a request. Creating the Views A view contains the HTML markup and content that is sent to the browser. A view is the closest thing to a page in an ASP.NET MVC application. You create a view by creating a file with the extension .aspx. Creating the Database The next step is to create the database that will contain our tasks. You can create the database by right-clicking the App_Data folder and selecting the menu option Add, New Item. Select the SQL Server Database template item, name the database TaskListDB.mdf, and click the Add button.
More →