Random Image

Featured Post

Mikuni Super BN (SBN) Carburetors Owner Manual


mikuni carburetors

The Super BN Carburetor for high performance applications is the latest a series of watercraft carburetors from Mikuni. The Super BN earns its name because of the increase performance it delivers over previous Mikuni BN Carbs. Installation Manual: Exercise care when changing carburetion components and any time you work with the fuel system on your watercraft. Work in a well ventilated area. Do not engage the starter while fuel lines are disconnected. Immediately clean up any fuel spill that might occur during carb installation. A: As when installing any performance product, a degree of mechanical ability is required. If after reviewing the parts and instructions you don’t feel that you can properly complete this installation, take your watercraft to a competent professional. Proper installation and adjustment will save time, money and aggravation. A: In most cases your new Super BN Carburetor will be installed in conjunction with an aftermarket manifold and flame arrestor/air filter system. We recommend using this manual, together with the applicable shop manual for your watercraft, and the instructions from the aftermarket manifold manufacturer to help you with the installation and tuning of the Super BN Carburetor.
Read More

Latest Posts

1997 - 2000 Honda CR-V Service Manual

This manual contains technical information for the 1997 - 2000 Honda CR-V. It is divided into 24 sections. The first page of each section is marked with a black tab that lines up with its corresponding thumb index tab on this page and the back cover. Each section includes: A ...
Categories: Honda, Automotive

2008 Honda CR-V Engine Block Heater Installation Instruction

Tools and Supplies Required: Phillips screwdriver, Flat-tip screwdriver, Ratchet, 10 mm and 24 mm Sockets, Torque wrench, Diagonal cutters, Heavy gloves, Drain pan, Tape measure, White marker, Coolant (Honda All-Season Antifreeze/Coolant Type 2), Blanket Drill, 3 mm and 7 mm Drill bits, 10 mm Hex wrench, Pushpin, Fender cover. Installation Procedures: ...
Categories: Honda, Automotive

Harley Davidson New Rear CAM Roller Bearing Assembly Service Bulletin

This service bulletin will guide you to remove and install the New Rear CAM roller bearing assembly on Harley Davidson motorcycle. Cam bearings may be a loose fit in the cam support plate. To avoid possible damage, be aware that camshaft and bearing assemblies may drop out at start of ...

1999 - 2000 Subaru Impreza WRX Workshop Manual

The Subaru Impreza WRX is originally introduced in 1992 in Japan, this is a turbocharged version of the Subaru Impreza, it is available as a sedan or wagon. The WRX had powered with a turbocharged flat-4 2.0L (then later a 2.5L), Subaru Boxer engine. Compared to the base Impreza, the ...
Categories: Automotive

BMW M70 Engine Mechanical and Manual

BMW M70 was produced at 1988 - 1996, powered with V12 piston engine and featured heavily in the 7-series and 8-series of the late 80's and early 1990s. The document follows is a BMW M 70 B 50 M/BMW 750i engine manual that helpfully to service and repairing your BMW ...
Categories: BMW, Automotive

BMW ZF-5HP-19 Transmission Technical Service Manual

This transmission is manufactured in Germany by ZF and carries the designation ZF-5HP-19. The ZF-5HP-19 Series is an electronically controlled, five speed automatic transmission with a lock-up clutch type torque converter. Two planetary gear sets, one Ravingneaux gear set and one standard planetary gear set on the output side, four ...
Categories: BMW, Automotive

Science

Gas Turbine Engine Compressor Simulation Design

The superior output power-to-weight ratio of the gas turbine engine has made it the mainstay of modern aviation propulsion for both civilian and military applications. The capability of producing high output power at low engine weight has also made it a common propulsion system in both marine and armored military ...
Categories: Engineering, Science

Hydraulic Design of Stormwater Pumping Station Using Programmable Calculators

Content Inside: This publication was prepared by the Hydraulics Branch, bride division office of engineering in Washington, D.C. Table of Content: Discussion of pumping station procedures, Introduction, development of a mass curve routing procedure, estimating required storage and pumping rates, stage storage relationship, stage discharge relationship, inflow mass curve, mass curve ...
Categories: Engineering, Science

Hydraulic Manipulator Design and Development with Mechanism/Pro

Content Inside: Highly flexible handling devices which carry loads or generate great forces, demand the use of hydraulic driven manipulators. Of crucial importance here are type and quality of the mechanism conveying motion between the jibs. This paper wil introduce designs of mechanism which can be applied to swing the arms ...
Categories: Engineering, Science

Hydraulic Design Manual

Content Inside: This manual provides guidance and recommended procedures for the design of Texas Department of Transportation drainage facilities. This revision updates various equations and references to them, updates the procedure for conduit design, and corrects minor errors. The manual contains fourteen chapters: Manual Introduction, Policy and Guidelines, Types of Documentation, ...
Categories: Engineering, Science


Page 1 of 19412345»...Last »